  |
 |
| Illuminated Components: An NRC Company | 561-241-8600 | Boca Raton, Florida |
|
|
|
APEM's
Panel-mount LED Indicators Now Available In 4 New Diameters |
 APEM
now offers the broadest range of LED indicators in the market:
- 7 diameters: 6, 8, 12, 14, 16, 19 and 22 mm, - 3 bezel styles: prominent, recessed and flush - 3 bezel finishes: bright chrome, black chrome and satin grey - 6 power supply voltages: 6VDC, 12VDC, 24VDC, 28VDC, 110VAC and 230VAC All the models are available with 5 LED colours - red, green, yellow, blue and white, as well as optional bicolour, tricolour and flashing LED's. Q series indicators can be supplied with solder lug/faston terminals, pins or 200 mm wires. Integral resistors permit direct connection. The options include high-brightness LED's (sunlight readable), panel sealing to IP67, custom engraving on flush bezel versions and plastic bezels on 16 and 22 mm.
|
|
Optek
Releases OPB733TR Surface Mount Reflective Sensor |
OPTEK Technology's OPB733TR series of reflective sensors is
designed to meet a growing demand for small footprint, surface
mount, reflective object sensors. The OPB733TR features a long
detection distance (.4" to 1"), higher resolution than previous
non-focused reflective sensors and a package that reduces ambient
light sensitivity.The OPB733TR is suited for a wide variety of applications in the office equipment, medical, industrial, consumer and gaming industries. Examples of applications include edge detection, mark detection, door sensor, industrial automation and proximity sensing to name a few. |
|
|
|
RELATED COMPONENTS
|
|
AVX's
Discrete Wire-To-Board Insulation Displacement Connectors |
|
Originally designed to accept
26AWG to 28AWG stranded or solid wires, the 9176 and 9177 series
have been added to now include 18AWG to 24AWG and 14AWG to 20AWG
respectively. This expansion opens up the market now across a
broader range of applications.
 The
value of this connector is achieved from the total applied cost of
the wire connection. This is achieved from the simplicity of the
connector and wire termination process. For starters, the 2
position and 3 position connectors are tape and reel packaged for
high volume SMT placement onto the PCB. The individual wires are
then located over the top of the contact and are simply and
reliably pressed into the slot via hand or arbor type press-in
tools. This process allows the contact tines to pierce the
insulation jacket which creates a gas tight connection, while
using plastic insulator features to securely grab the insulation
providing a strong strain relief on the final assembly. There is
no wire stripping or preparation needed prior to termination.
Contact material is phosphor bronze, with three re-terminations
achievable for each individual contact. These connectors are
unlike anything currently available on the market, as they have a
smaller footprint, are end-to-end stackable and assembling the
wires to the connector is very easy. AVX discrete wire IDC connectors are manufactured with high temperature nylon material to withstand RoHS reflow processes and high working temperatures. The IDC connectors are based on automotive level temperature and vibration specifications, resulting in products that are robust and suitable for a wide variety of harsh operating conditions. With such a broad wire range accommodated within the product series, a wide variety of applications within the Industrial, Medical, Automotive and Transportation markets. The LED lighting market is a perfect fit for this type of connector, for use in LED lighting strips for sports arena signs, display cases, lighted cabinets, advertising signs, and architectural lights used for building feature enhancement or internal feature lighting. |
|
TDK's
Double-Layer "Supercapacitor" Offers Lowest ESR In The Industry |
|
(February 2009):
TDK's new electric double-layer "Supercapacitor" offers the
lowest ESR in the industry for this size Mount. The new
capacitor, which will be available in a 20x20 mm size, will be
featured at the TDK booth at APEC this week in Washington D.C.
The EDLC employs a double layer of charged particles formed
on activated carbon coated electrodes in an electrolyte. As a
result, high capacitance is achieved due to the large electrode
surface area and thin charge-bearing layer.
TDK's EDLC Supercapacitors leverage TDK's core technologies in
high-quality film coating and process control, in combination
with extensive mass production capabilities for high-density
energy storage devices. By careful optimization of design,
materials selection and production method, TDK is able to
deliver best-in-class performance, in a high-quality monolithic
Supercapacitor package.
TDK's new EDLC Supercapacitor is targeted at portable device applications such as High Power LED Flash. In this application, the characteristics of the Supercapacitor enable the use of the latest high current LEDs to produce camera flash illumination of similar performance to existing Xenon flash solutions, but without the need for high voltage components and complex charging circuits. Other applications include Pulsed Energy Storage, Power Loss Assist and Battery Assist.
|
Main
Characteristics of the EDLC272020-501-2F-50|
Jaro's
'Push-Pull' Super-Flow-Turbo Is Freezing Cold! |
 Jaro
Thermal's newest 'Super-Flow-Turbo' series of 'front to back'
counter-rotating fans produces an impressive static pressure of
2.44 inches in H2O. Measuring in at 60 x 60 x 76 MM, the new
dual-fan combination is perfect for automotive and power-supply
applications that require ultra-high output. To exceed today's
toughest environmental requirements, the extended temperature is
-30 degrees C to +90 degrees C at 65% +/- 20% relative humidity.
Standard options include IP-55 water protection, on-board PWM
control, alarm output, tachometer output, thermistor controls and
more. To top it off, the life expectancy is 70,000 HOURS AT 40
degrees C / 65%. This industry-leading combination brings the
newest Super-Flo-Turbo to the top of today's thermal cooling
revolution. For more information on the Turbo series or any of
JARO Thermal's other cutting edge products, please contact Dennis
Eisen at d.eisen@jarothermal.com or visit their website at
www.jarothermal.com. |
|
Gap
Pad and Gap Filler (Thermally Conductive) Interface Materials From
Bergquist |
 Gap
Pad and Gap Filler are cost-effective, filled, thermally
conductive interface materials. With shock dampening abilities,
the Gap Pad line is recommended for applications that require a
minimum amount of pressure between components. It's "gel-like"
modulus makes it well suited in areas where conformity may be a
priority. Gap Pad and Gap Filler are also available in a silicone-free form.These thermally conductive polymers are designed to have similar mechanical benefits as silicone materials. They are ideal for sensitive applications that do not allow silicone, such as underwater pools and automotive lighting applications. |
| Thermally Conductive Bond-Ply Adhesives From Bergquist |
 Bond-Ply
is a thermally conductive, pressure sensitive adhesive tape,
available in either fiberglass reinforced or unreinforced. With
its ability to have a high bond strength, it can eliminate the
need for screws, clipmounts or fasteners.
· Good thermal performance
· Immediately bonds to target surface · Eliminates need for mechanical fasteners or screws · Alternative to heat-cure adhesives
|
|
Bergquist's "TIC" High performing, Thermally Conductive Grease
|
 TIC
is a high performing, thermally conductive grease designed for use
as a thermal interface between an aluminum base and a heat sink or
metal casing.The compound wets-out the thermal surfaces and flows
to produce the lowest impedance for your LED application.
· High thermal performance
· Good thermal conductivity · Can be screened · No post "cure" required · Room temperature storage · Exceptional value A thermally conductive liquid silicone adhesive (called "Liqui-Bond") is also available. Liqui-Bond cures to a solid bonding elastomer. Liqui-Bond features excellent low and high-temperature mechanical and chemical stability. It can be supplied in either a tube or mid-sized container form. |
|
About Illuminated Components
|
|
Illuminated Components is a leading, full-solution provider of LED
products, services and solutions. Illuminated Components specializes
and focuses on lighting designers and OEMs who require efficient,
innovative, lighting technologies. Illuminated Components has a
knowledgeable "ON DEMAND" support team ready to provide LED lighting
expertise, resources, recommendations, and logistics support - from
start to finish. Our goal is to exceed your highest expectations.
6600 Park of Commerce Blvd, Boca Raton, FL 33487 | Tel
561-241-8600 | Fax 561-241-3328
|
| Quote Request Speak With Us Expertise & Background |